Commercial spot graphics + lettering
From $1,795A complete, readable business-identity package—not a single mailbox decal.
Request this wrap quoteUse these ranges to plan your project, then send photos and the coverage you want for a quote. Final scope depends on the vehicle or trailer, artwork, existing graphics, surface condition, and installation work. The package descriptions below show what is included.
Planning a mobile food business? Explore our trailer and food truck wraps and use the design checklist to account for serving windows, doors, vents, and panel seams.
Fast budget check
Pick the real scope.
This is a planning tool—not a bait-and-switch instant quote. Photos, measurements, artwork, surface condition, openings, hardware, and install access still control the final written number.
Planning range
Plan from $5,900High-impact commercial coverage on a clean, wrap-ready sedan.Installed wrap project in Stillwater, MN. Tell us your location and preferred timing.Request this wrap quoteTypical planning ranges
Budget with your eyes open.
Ranges are before sales tax and assume clean, sound, wrap-ready surfaces.
Partial trailer graphics
From $3,495Focused coverage for a strong mobile billboard without wrapping every panel.
Request this wrap quote8.5×16 trailer · 3 sides · ready art
From $4,995Two long sides plus the rear when usable production art is supplied.
Request this wrap quote8.5×16 trailer · 3 sides · custom design
$5,595Our benchmark package: measured scope, custom design, production, laminate, and install.
Request this wrap quote8.5×16 trailer · 4 sides · custom design
$6,495Two long sides, front, and rear on a clean, sound, wrap-ready trailer.
Request this wrap quote8.5×20 trailer · 4 sides · custom design
$7,195Two long sides, front, and rear on a clean, sound, wrap-ready 20-foot trailer.
Request this wrap quoteComplex food + concession trailer
$8,500–$9,500+Menus, openings, vents, trim, hardware, sponsor zones, and difficult layout are scoped individually.
Request this wrap quote3/4 car wrap
Plan from $5,900High-impact commercial coverage on a clean, wrap-ready sedan.
Request this wrap quoteFull car wrap
Plan from $6,250Premium conformable film, matched laminate, standard custom design, and install.
Request this wrap quoteSmall SUV wrap
Plan from $6,750Coverage and access vary by body style, trim, roof, and hardware.
Request this wrap quoteCommercial cargo van wrap
Plan from $8,450Standard-body planning figure; high roofs, removals, racks, and repairs are additional.
Request this wrap quoteCompare every bid
Same square footage. Different quote.
Before choosing the lowest total, ask every shop to confirm these six lines in writing.
Exact coverage
Every side, panel, roof area, window, bumper, trim piece, and add-on should be named—not implied.
Design + proofing
Confirm the included design allowance, proof rounds, production setup, and what happens if dimensions change.
Job suitability
Confirm the quoted construction is appropriate for the surface, geometry, exposure, expected life, and removal plan.
Prep + removal
Old graphics, adhesive, oxidation, silicone, damage, cleaning, disassembly, and repairs should have a clear owner.
Install + downtime
The quote should state access, crew assumptions, install location, expected schedule, and vehicle or trailer downtime.
Corrections + exclusions
Know who pays for an incorrectly produced approved panel and which changes, taxes, travel, or hidden conditions are extra.
Already have another quote? Send it with photos. We will identify scope differences before asking you to decide.
Compare my quote ↗Shipped + fast-turn products
Built for the job. Ready to ship.
These are controlled starting scopes. Fitment, art, quantity, finishing, freight, and requested timing still control the written order.
Snowmobile wrap kit
From $799Model-specific, laminated graphics with one proof round, panel labels, and install map. Fully custom illustration is quoted separately.
Price this kit ↗UTV / side-by-side wrap kit
From $1,499A tougher, replacement-ready graphic system for full-body UTV layouts, race programs, rentals, and branded work units.
Price this kit ↗ATV / quad wrap kit
From $899Cut for the verified plastics and built as a coordinated package rather than a loose stack of generic stickers.
Price this kit ↗Print-ready decal starter run
From $279Contour-cut, laminated outdoor decals; size and quantity control the final count.
Price this job ↗3×6 finished banner
From $179Printed banner with standard hems and grommets for normal promotional use.
Price this job ↗4×8 finished banner
From $249Printed banner with standard hems and grommets; wind exposure can change construction.
Price this job ↗10 yard signs + stakes
From $399Standard two-sided 18×24 signs from print-ready art.
Price this job ↗DIY window lettering kit
From $329Cut vinyl, masking, layout guide, and application instructions.
Price this job ↗What is inside the number
A complete wrap system.
The quote accounts for the design, production, finishing, preparation, installation, and quality control needed to deliver a finished commercial asset.
Measured coverage
The quote states which sides, panels, roof areas, windows, bumpers, trim, and add-on pieces are included.
Job-specific construction
We specify the complete system for the actual surface, geometry, exposure, expected life, and removal plan.
Finished production
Printed area, ink coverage, panel waste, lamination, trimming, contour cutting, inspection, and staging are built into production.
Skilled install + inspection
Prep, crew-hours, access, alignment, edge work, post-heat where required, and the finished walk-through are scoped before install.
Cars · trucks · vans
Specified for the job.
Surface and geometry reviewed before quotingExposure and expected service life consideredInstallation and future removal planned togetherTrailers · box trucks
Inspection decides the construction.
Skin condition, seams, rivets, and corrugations inspectedDifficult surfaces tested before productionEvery specification checked against current guidanceNo surprise reprint invoice
Our mistake? Our cost.
If we misproduce an approved panel, we correct it. If you add pieces, change the design, alter dimensions, or expand the scope, we price the change in writing before production. That is the line.
Pricing questions
Know before you approve.
How much does an 8.5×16 trailer wrap cost in Minnesota?+
For a clean, wrap-ready 8.5×16 trailer, our published planning prices are from $4,995 for three vertical sides with usable print-ready art, $5,595 for a custom-designed three-side package, and $6,495 for a custom-designed four-side package. A clean 8.5×20 four-side custom package plans at $7,195. Openings, removals, repairs, unusual skins, roofs, floors, and added pieces can change the written quote.
How much does a food truck or concession trailer wrap cost?+
Complex food and concession trailers typically plan at $8,500–$9,500+. Serving windows, doors, menus, vents, trim, hardware, sponsor areas, and difficult layout add production and installation work beyond a smooth cargo trailer.
Are these the cheapest wrap prices in the Twin Cities?+
We do not promise to be the cheapest line item. We publish realistic planning figures and spell out the design, coverage, preparation, production, installation, exclusions, and correction responsibility so you can compare complete scopes instead of teaser prices.
How should I compare two wrap quotes?+
Ask both shops to identify the exact sides and panels covered, design and proof allowance, surface preparation, installation and downtime, exclusions, tax, warranty terms, and who pays if an approved panel is produced incorrectly.
Why is wrap pricing shown as a range?+
Two vehicles with the same model can require different preparation, coverage, hardware removal, paneling, film, and install time. The range helps with budgeting; the written quote locks the exact scope after photos, measurements, and inspection.
How do you choose the right wrap construction?+
We do not publish a one-size-fits-all product list. We specify the complete construction after reviewing the actual surface, geometry, exposure, expected life, removal plan, and current manufacturer guidance.
Do trailers use the same construction as cars?+
Not automatically. A smooth trailer skin, compound vehicle curves, rivets, corrugations, oxidation, and difficult adhesion create different requirements. We inspect the unit and confirm the appropriate construction before the quote is approved.
Will I be charged if you misprint a panel?+
No. If we produce a panel incorrectly after the approved proof and documented specifications, correcting that production error is our cost. Customer-requested revisions, new pieces, changed dimensions, hidden conditions, or added scope are priced with a written change order before we proceed.
What is excluded from the planning range?+
Sales tax, old graphic removal, failing paint, rust, oxidation, body repair, silicone remediation, lifts, unusual travel, rush production, and customer-added scope are excluded unless the written quote specifically includes them.
How much is due to start?+
Unless your written order says otherwise, a 50% production deposit is due before design scheduling or material allocation, with the balance at completion before pickup or before shipment, subject to applicable law. Printing also requires the accepted order and terms, confirmed fitment, and written approval of the identified final proof. Payment alone is not artwork approval.
Photos beat guesses